How to Get Bearings Out of Skateboard Wheels? Simple 5 Steps
The bearing has a huge role in your skateboard’s performance. It is responsible for the wheels’ speed and smooth roll. However, this part is often beat-up because of intense use.
Much more, dirt, dust, and rust between the gaps will most likely occur, causing its resistance. For sure, these circumstances can decrease the speed of your skateboard, or much worse; it can lead to accidents.
Regular maintenance of the bearing is key for your skateboards’ lasting performance. There is no need to visit your local skate shop to clean or change the bearings. Preserving the skateboard bearing is easy. It starts by removing the bearing from the wheel.
This article will guide you in a step by step process of removing the bearings. Read on and learn how to get the bearings out of your skateboard wheel in 5 simple steps.
Make sure you have all tools necessary before you start so that you can work spontaneously.
- Skate tool or a ½” socket wrench
- Screwdriver, bearing puller, metal rod
- Small tray to organize the parts
Get Skateboard Bearings Out in Simple 5 Steps
Now that you have the tools required, let’s get going!
Step 1: Unbolting the Wheel
Start with your skateboard deck; make sure that it is on its side. The wheel is attached to the axle, so this part has to point upward.
Using the skate tool or the wrench, loosen the axle nut and remove the washer or the speed ring. Put the nut and washer aside. You can place it in a small tray for easy organization.
Do this to all four wheels if you need to clean or replace all bearings. But if you already know which one to replace, remove only the nut and speed ring from that particular wheel.
Once the nuts and washers are out, carefully take the wheels out of the axle. Now you will find the bearings visible from both sides of the wheel.
Step 2: Getting Ready to Pry the Bearing
Now that you have the wheels, you can remove the bearings either by hand or tools. Study the methods on how to remove the bearings by hand or tools and see what suits you best.
1st Way: By Hand
Although a tool is an advantage in detaching the bearing from the wheel, it is not necessary. You can use your hand and the axle of the truck to do it. However, if you opt to use this method, you need to be very careful.
Do not apply too much force because this can damage the bearings.
2nd Way: By a Hand Tool
If you think using the axle of the truck to remove the bearing is risky, you can use a hand tool instead. A screwdriver can be used to pry the bearings out of the wheel. You can also use a metal rod in detaching the bearing.
Make sure you use a rod that fits perfectly in the bearing.
3rd Way: By a Special Tool
Some skate shops use special tools to remove the bearings from the wheel. They use a skateboard bearing puller or skateboard bearing presser to ensure that the bearing will be taken off safely.
This is also a faster way to accomplish the task.
Step 3: Yank the Bearings out of the Wheel
There are a few ways to pull out the bearings from the wheel. Each of these methods is simple to perform. Depending upon your preference or maybe need, either way will definitely work just fine.
1st Way: Using the Axle of the Truck
To remove the bearing using the axle of the truck, start by placing the wheel back to the axle. When the wheel is halfway in, make sure that the axle tip only touches the inside bearing. Then gently yank the bearing out at an angle.
Use the motion like you are opening a bottle of a beer. Sometimes the bearing does not go all out with the first pry. If this happens, do not force the bearing out at the same angle. This can damage the bearings.
Instead, try to yank the bearing out from a different position. You can also use a back and forth motion until you get the bearings out.
2nd Way: Using a Screwdriver
Simply insert the screwdriver in the wheel until the tip is at the edge of the interior bearing. Then slowly yank it off at an angle.
Attempting once might not take the bearings out completely. You can position the pry at a different angle then try it again.
Do this whole process carefully to avoid damaging the bearings.
3rd Way: Using a Metal Rod
The metal rod must fit perfectly in the hole of the bearings' inner ring. Slowly drive the rod in the bearing. Then gently tap the rod using a hammer.
Be cautious of this method because it can easily break the bearings apart.
4th Way: Using a Bearing Puller
When using the bearing puller, the wheel must lay flat on a surface. Just plug the metal rod in the bearing then press down the button to drive the rod in the wheel.
Once the tip of the rod reaches the trim of the first bearing, it will click. This indicates that the bearing is locked and ready to be pulled out.
5th Way: Using a Skateboard Bearing Presser
At the other end of the skateboard bearing presser, there is a rod with the catch tip. Simply slide the wheel until it reaches the edge of the first bearing. You will know that it is in place because it clicks. Then push the handle down to tug off the bearing.
Step 4: Removing the Spacer
Skateboard wheels have 2 bearings each. These bearings are separated with a spacer. And these bearing spacers are important in making your turns stable and smooth.
When you have removed the first bearing, you may also take out the spacers. Place them in the small tray and ensure that they are not misshapen.
Step 5: Repeat on Reverse
You have taken the first bearing out as well as the spacers. Now, you need to remove the second bearing from the wheel. Do that by flipping the wheel over and follow the same process that you did for the first bearing.
Voila! You’re done. Without a doubt, this guide provides an effortless and stress-free procedure on how to get the bearings out of your skateboard wheel.